艾浩尔藤草工艺品完全防霉解决方案清洗设备

艾浩尔藤草工艺品完全防霉解决方案

艾浩尔藤草工艺品完全防霉解决方案2018-01-10 10:59核心提示：根据我司防霉工程师至贵司实地现场进行考查，依据贵司工艺品材料结构加工工艺，结合艾浩尔系列防霉产品之功效，建议按照以下文章流程处理，可有效防止工艺品受潮、霉变的问题，确保您的产品安全运送到国内外客人手中。藤草工艺品完全防霉解决方案 根据我司防霉工程师至贵司实地现场进行考查，依据贵司工艺品材料结构加工工艺，结合艾浩尔系列防霉产品之功效，建议按照以下流程处理，可有效防止工艺品受潮、霉变的问题，确保您的产品安全运送到国内外客人手中。 Solution of Mildewproof Rattan Artwork Author：Guangzhou AiHaoEr Mildewproof antibacterial technology Co., Ltd.(Network Department) Date：April（19th），2016 Class:Technical solution According our mildewproof engineers went to wood -sound box factory, observed and studyed the structure material and processing technology ,we found venders could treat mildew problem by following methods which can prevent damp and mildew for rattan artwork,and last clould ship safety product for forign clients. 一、材料控制ONE Material control 1、竹编制品及木、藤、芒、葵、草等用iHeir-JP竹木防霉抗菌剂药水浸渍应使竹、木、藤、草及其制品在浸渍后增重15%-20%（大约5—10分钟）。备注:浸泡液体按照1：20的配制(5kg竹木防霉剂 : 100kg水)。竹、木、藤、草及其制品全部浸入配好的药水中（勿露出水面），达到增重15%-20%后，取出滴干药水，风干或晒干后包装入库。本产品制备的药水性质稳定，可反复使用，不必废弃。但药液不能浸没竹木制品时应及时添加药液，补充药液按更高的比例配制。 No.1Bamboo &wood products and prodcuts are made from such as rattan, fern, kwai, grass should soak with iHeir - JP （Bamboo /wood Anti-mold Agent）, and then they would gain weight 15% to 20% after dipping (about 5-10 minutes).Note: ?the preparation of the soakiong liquid as 1:20 (5 kg ?Bamboo /wood Anti-mold Agent: 100 kg of water).Bamboo, wood, rattan, grass, and all products into prepared potions (not above water), after gained weight 15% - 15%, remove the ?potions, and ?please air dry or ?sun dry before packaging in warehousing .The potions of this product is stable, can be used repeatedly, no wastely.But when the solution cannot ?immerse wood products should add liquid medicine in time , and supply the iquid medicine according to the higher proportion. 2、胶水特别是环保胶水，在使用前必须在胶水里面添加1~2%的胶水专用防霉抗菌剂iHeir-JS，以免为细菌提供了营养源，引起微生物的繁殖。 No.2 Adding 1~2% of iHeir-JS (Gluewater Anti-mold Agent ) before using environmental glue.Because environmental glue is easly to offer ?nutrient source that caused microbes grow. 3、密度板、中纤板、木材应该控制湿度，建议将木材的湿度控制在12%以下，湿度超过14%应做防霉处理，简单的方式是在木架上用毛刷刷上一层竹木防霉抗菌剂iHeir-PT，如果木材表面有做油漆，建议在油漆里面添加1-2%的iHeir-YQ油漆专用防霉抗菌剂（环保原因，现在的油漆没有添加任何防腐杀菌药剂），抑止霉菌、细菌等微生物的生长。 No.3It must control the humidity of density board, MDF and wood .It’s recomemded control under 12% of humidity.If exceed 14% should do some anti-mold treatment.The simple way is to brush with wool on the surface of Bamboo /wood Anti-mold Agent iHeir - PT.If the surface need to ?painted that recommend adding 1-2% of iHeir -YQ Paint Anti-Mold Agent(As for environmental for nature and human,today the paint does not add any agent to mould and antibacteria.),which prevents the growth of mold, bacteria and other microbes. 4、在成品各个表面放置Dc.odorban防霉贴，包装成品的纸皮、塑料袋应该保持干净整洁，建议将湿度控制在12%以下，包装时将纸皮、塑料袋尽可能的全部包装到工艺制品，使其相对密闭，Dc.odorban防霉贴通过释放抗菌因子在密闭的空间里杀死细菌和抑制细菌生长，使其达到防霉抗菌效果。注：产品依其规格大少进行适当放置Dc.odorban防霉贴数量的增减。 No.4Put Dc.odorban anti-mold chipson surface of finished products.Keep paper and plastic bags who is used for pakage for peoducts clean ,the humidity should control under 12%.When packaging,it has better to cover the craftworks completely.Dc.odorban chips kills bacterials and mold by releaseing anti-mold factors which has good effect to prevent mold growing.Note:According its specifications of products ? to place Dc.odorban chips properly. 5、在工艺品成品包装袋里面放置H-10防霉干燥包，使其达到降低产品因受潮霉变的风险。 No.5Put some H-4 anti-mold desiccants in packaging bag would reduce the risk of mildew. 二、仓库控制TWO Warehouse control 1.竹编制品及木、藤、芒、葵、草等以及成品不要直接堆在地板上，应使用栈板隔开，且离墙体＞10CM。 No.1Bamboo products and wood, rattan, fern, kwai, grass, etc, these finished products shouldn’t pile up on the floor but should use pallets to separate,and far away from wall about 10 centimeter. 2.材料仓、成品仓应每月进行一次杀菌处理，结合贵司实际情况，首先保持地面的清洁卫生，面料、包材、成品仓开始头三个月每月一次，三个月后每三个月一次进行杀菌处理，用iHeir-Spray杀菌剂5%加到地拖水中拖地一次（注：梅雨季节应每月一次）。 No.2The material warehouse and finished product warehouse should have sterilization treatment once month.According practical situation of your company, first of all ,keep the floor clean. The plus material ,packaging materials and finished product warehouse then do a antibacterial treatment with iHeir - Spray(5%) every month at the start three months ,and after these three months should do it every three months .(Use method:add iHeir-Spray in water ,then mop the floor.)Note:treating once month during Meiyu reason . 3.材料仓、成品仓库因注意通风，当室外的湿度大于室内湿度，关闭门窗，反之打开门窗，记录湿度、温度变化，如果潮湿季节室内相对湿度≥80%。应安装抽湿设备或加放仓库专用杀菌包，以降低产品受潮霉变的风险。 No.3Let air circulates in materials ?warehouse and finished products warehouse.When the outdoor humidity is greater than indoor humidity, close the doors and windows.If oppositely,open the windows and doors, record the change of the humidity and temperature.If relative humidity is over 80% during Meiyu season,should install moisture-removal equipment or put some ?antimicrobial desiccants in warehouse,which reduce the risk of mildew for products. 三、集装箱结合控制 1.检查通风孔及密封设施是否完好，是否渗漏变形。 No.1Check the shaft and esaling facilities are in good condition whether have problem of leakage or deformation. 2.集装箱应该清洁、无油污、无异味，为避免交叉感染。建议在集装箱内喷杀菌剂iHeir-Spray（每柜500g/支）。 No.2The cotainer should keep clean ,no oil and no peculiar smell.We recommended that spraying iHeir - Spray to avoid cross infection.( 500 g a container). 3.装货后，为避免海洋运输气候变化引起的（“集装箱雨”）潮气，建议在集装箱内壁悬挂集装箱防霉棒，每间隔2-3M/条。 No.3After loading,in order to avoid moisture " the container rain ",it’s recommanded that placed dry rods every 3m at the top of the container. 如有其它疑问，我司可提供技术支持与专业指导，也可派专人上门现场指导。 If have any questions ,we would like to offer support of technology and professional guidence ,include that appointing our experts for you. 想了解更多防霉知识,可联系艾浩尔聂小姐15920591954 或加QQ:732138585 ?邮箱:nhm723798562nhm@foxmail.com 广州艾浩尔防霉抗菌科技有限公司

皮肤科在线医生

周口治疗白斑病哪个医院比较好

毫州治疗尿道炎好的医院

治疗前列腺炎医院

太原男性白癜风医院